Catalogue MAGNETICS, "Molypermalloy Powder and High Flux cores", http://www.mag-inc.com , février 2002.
Copyright - [Précédente] [Première page] [Suivante] - Home

Fiche : [DATA007]

Titre : Catalogue MAGNETICS, Molypermalloy Powder and High Flux cores, http://www.mag-inc.com , février 2002.

Cité dans : [DIV002]  Liste des librairies et des catalogues constructeurs, décembre 2014.
Cité dans :[LIVRE019] J.-P. FERRIEUX, F. FOREST, Alimentations à découpage - Convertisseurs à résonance, 2e édition revue et augmentée, 1994.
Cité dans :[LIVRE122] J.-P. FERRIEUX, F. FOREST, Alimentations à découpage - Convertisseurs à résonance, DUNOD, 3e édition revue et augmentée, 1999.
Cité dans : [DIV143]  T. LEQUEU, Informations diverses sur les ferrites et les circuits magnétiques, septembre 2001.
Cité dans : [DIV169]  Allstar Magnetics Home Page, Distributeurs de composants magnétiques, http://www.allstarmagnetics.com/
Société : Magnetics, Inc.

Vers : Inductor Design Using Powder Cores
Vers : Litteratures
Site : http://www.mag-inc.com
Info : Ferrite Cores, Bobbins, Hardware, MPP, High Flux, Tape Wound, Kool Mu


Inductor Design Using Powder Cores

TOP

Lien : PCD-3_1.zip - 1138 Ko, (PCD-3.1, Sep 14 2001), le 8 janvier 2002.

MAGNETICS® "Inductor Design Using Powder Cores" is an aid to assist design engineers in selecting the optimum core for inductor applications, specifically in switch-mode power supply (SMPS) output filters, also known as DC Inductors. As this name implies, most of the current flowing through the inductor is DC, with some amount of AC 'ripple' current (noted as Idelta) included as well (Figure 1).

Depending on the particular SMPS design, this ripple current value can either be insubstantial compared to the bulk DC output current in the inductor, or it may be quite large, and potentially limit the overall inductor design due to loss and temperature rise constraints. This software package selects core sizes and materials largely to provide the smallest package size that will support the needed inductance and current, but also allows users to select deliberately larger cores with the intent of reducing losses and lowering the component's temperature rise. Much more information on these topics is included in the Online Help sections distributed with the software, as well as in a number of other technical papers included in the Help file's Reference section.

MAGNETICS Inductor Design Using Powder Cores Software uses a design algorithm intended to specify the smallest design package size for the given input parameters (currents, inductance values, frequency, etc.). The program sizes the appropriate core based on the needed energy product, expressed as the full load inductance times the square of the peak (DC plus ripple) current flowing through the inductor. Of course higher inductance values and higher current levels imply a larger core size.

Typical inductor designs will specify at least the required minimum inductance at full load current and the DC current in the windings. Additional information, such as the amount of AC 'Ripple Current', current density (or wire size), highest acceptable temperature rise, and the maximum inductance at zero load current may also be supplied and can help to more accurately select the best core for the design.

To download this software, right-click on the link link below, and select "Save As" from the pop-up menu. You will need software such as WinZip to un-zip and install the program. Get WinZip® now.

This software runs under Windows 95/ 98SE/NT/2000. Some Windows 95 users may experience problems due to an old release of the operating software. Patches included in the ZIP files will fix some problems. If problems persist, try updating to the latest service pack, or contact a MAGNETICS Application Engineer for more help.


Litteratures

TOP

Lien : Magnetic/fc-s3.pdf - x pages, 1978 Ko.
Lien : Magnetic/cg-01.pdf - x pages, 436 Ko.
Lien : Magnetic/cmf-3_0.zip - x pages, 1169 Ko.
Lien : Magnetic/fc-s1.pdf - x pages, 221 Ko.
Lien : Magnetic/FC-S2.pdf - x pages, 325 Ko.
Lien : Magnetic/CAD-1_3.zip - x pages, 64 Ko.
Lien : Magnetic/fc-s4.pdf - x pages, 116 Ko.
Lien : Magnetic/fc-s5.pdf - x pages, 126 Ko.
Lien : Magnetic/fc-s7.pdf - x pages, 284 Ko.
Lien : Magnetic/fc-s8.pdf - x pages, 271 Ko.


Mise à jour le lundi 10 avril 2023 à 18 h 48 - E-mail : thierry.lequeu@gmail.com
Cette page a été produite par le programme TXT2HTM.EXE, version 10.7.3 du 27 décembre 2018.

Copyright 2023 : TOP

Les informations contenues dans cette page sont à usage strict de Thierry LEQUEU et ne doivent être utilisées ou copiées par un tiers.
Powered by www.google.fr, www.e-kart.fr, l'atelier d'Aurélie - Coiffure mixte et barbier, La Boutique Kit Elec Shop and www.lequeu.fr.